Search Results

AUTOSAR is finding its way into the automotive industry. European automotive manufacturing companies were the early adopters defining and promoting AUTOSAR standard. One of the main AUTOSAR goals is to improve containment of product and process complexity and risk. Increased scalability and flexibility to integrate and transfer functions is another important goal of AUTOSAR. Working with different suppliers and vendors and respect their confidentiality makes the process of application software development even more complex. Presented in this paper is a creative way of utilizing AUTOSAR to overcome the integration challenges in a multi-party object code based software integration. The run time environment (RTE) files for the application software are generated through a set of scripts to automate the process for consecutive releases. The low level device drivers are configured by one supplier and are being used by another supplier through a set of AUTOSAR client-server operation calls.

The impact of Reynolds number on the aerodynamics and operational performance of commercial vehicles is discussed. All supporting data has been obtained from published experimental and computational studies for complete vehicles and vehicle components. A review of Reynolds number effects on boundary layer state, unsteady and steady flow, time dependent wake structure, interacting shear layer and separated flows is presented. Reynolds number modeling and simulation criteria that impact aerodynamic characteristics and performance of a commercial vehicle are shown. The concepts of dimensional analysis and flow similarity are employed to show that aerodynamics of commercial ground vehicles is only dependent on Reynolds number. The terminology of Roshko is adopted for discussing the variation in drag with Reynolds number in which the subcritical, transitional and transcritical flow regimes are defined for commercial vehicles.

Annual fuel use for sleeper cab truck rest period idling is estimated at 667 million gallons in the United States, or 6.8% of long-haul truck fuel use. Truck idling during a rest period represents zero freight efficiency and is largely done to supply accessory power for climate conditioning of the cab. The National Renewable Energy Laboratory’s CoolCab project aims to reduce heating, ventilating, and air conditioning (HVAC) loads and resulting fuel use from rest period idling by working closely with industry to design efficient long-haul truck thermal management systems while maintaining occupant comfort. Enhancing the thermal performance of cab/sleepers will enable smaller, lighter, and more cost-effective idle reduction solutions. In addition, if the fuel savings provide a one- to three-year payback period, fleet owners will be economically motivated to incorporate them.

1 One issue raised by the use of austenitic stainless steels in commercial vehicles is the increase in material costs. To reduce those material costs, a nitric acid electropolishing treatment was applied to SUS436L (18 Cr - 1.5 Mo - 0.4 Nb) and corrosion tests were conducted to compare its corrosion resistance to that of SUS316L(16 Cr - 12 Ni - 2 Mo). Compared to SUS316L, SUS436L subjected to nitric acid electropolishing indicated superior corrosion resistance. In addition, XPS and TEM analyses showed that while the SUS436L passivation film layer contained approximately twice as much chromium, its thickness was also generally reduced by approximately half, to 2 nm. These results suggest that electropolishing with nitric acid, which is highly oxidative, formed a fine passivation film.

The cyclic material behavior is investigated, by strain-controlled testing, of 8 mm thick sheet metal specimens and butt joints, manufactured by manual gas metal arc welding (GMAW). The materials used in this investigation are the high-strength structural steels S960QL, S960M and S1100QL. Trilinear strain-life curves and cyclic stress-strain curves have been derived for the base material and the as-welded state of each steel grade. Due to the cyclic softening in combination with a high load level at the initial load cycle, the cyclic stress-strain curve cannot be applied directly for a fatigue assessment of welded structures. Therefore, the transient effects have been analyzed in order to describe the time-variant material behavior in a more detailed manner. This should be the basis for the enhancement of the fatigue life estimation.

The regulatory requirement in Economic Commission for Europe (ECE R58) regulation applies to the Rear underrun protection devices which are intended to be fitted to commercial vehicles of N categories. The purpose of this regulation is to offer effective protection against underrunning of vehicles. This paper describes Computer aided engineering (CAE) methodology for testing rear underrun protection devices with loading sequences to be decided by Original equipment manufacturer. A sample model is prepared and analyzed to represent actual test conditions. Constraints and boundary conditions are applied as per test of vehicle. Finite element simulation is carried out using LS DYNA solver. Structural strength and integrity of Rear under protection device assembly is observed for different regulatory load requirement.

The lifting and excavating industry are not as advanced as automotive in the use of modern CAE tools in the early stages of design and development of heavy machinery. There is still a lack of confidence in the integrity of the results from FE simulations and optimisation and this becomes a barrier to the adoption of virtual prototyping for vehicle verification. R&D of Tata Steel has performed tests on two forklift truck overhead guards supplied by a major manufacturer. Based on the international standard for Falling Object Protective Structures (FOPS) as an initial input to the method of testing, the main aim of this study was to generate as much test data as possible to correlate the Finite Element (FE) simulations of two tests - a static and a dynamic test. The static test was developed to deform the overhead guard plastically in a slow controlled manner, so it would be easier to correlate the measured data to FE simulation.

To reduce heat transfer between hot gas and cavity wall, thin Zirconia (ZrO2) layer (0.5mm) on the cavity surface of a forged steel piston was firstly formed by thermal spray coating aiming higher surface temperature swing precisely synchronized with flame temperature near the wall resulting in the reduction of temperature difference. However, no apparent difference in the heat loss was analyzed. To find out the reason why the heat loss was not so improved, direct observation of flame impingement to the cavity wall was carried out with the top view visualization technique, for which one of the exhaust valves was modified to a sapphire window. Local flame behavior very close to the wall was compared by macrophotography. Numerical analysis by utilizing a three-dimensional simulation was also carried out to investigate the effect of several parameters on the heat transfer coefficient.

Diesel engine manufacturers strive towards further efficiency improvements. Thus, reducing in-cylinder heat losses is becoming increasingly important. Understanding how location, thermal insulation, and engine operating conditions affect the heat transfer to the combustion chamber walls is fundamental for the future reduction of in-cylinder heat losses. This study investigates the effect of a 1mm-thick plasma-sprayed yttria-stabilized zirconia (YSZ) coating on a piston. Such a coated piston and a similar steel piston are compared to each other based on experimental data for the heat release, the heat transfer rate to the oil in the piston cooling gallery, the local instantaneous surface temperature, and the local instantaneous surface heat flux. The surface temperature was measured for different crank angle positions using phosphor thermometry.

This study evaluated the ISO 5353 Seat Index Point Tool (SIPT) as an alternative to the SAE J826 H-point manikin for measuring military seats. A tool was fabricated based on the ISO specification and a custom back-angle measurement probe was designed and fitted to the SIPT. Comparisons between the two tools in a wide range of seating conditions showed that the mean SIP location was 5 mm aft of the H-point, with a standard deviation of 7.8 mm. Vertical location was not significantly different between the two tools (mean - 0.7 mm, sd 4.0 mm). A high correlation (r=0.9) was observed between the back angle measurements from the two tools. The SIPT was slightly more repeatable across installations and installers than the J826 manikin, with most of the discrepancy arising from situations with flat seat cushion angles and either unusually upright or reclined back angles that caused the J826 manikin to be unstable.

The base design of commercial vehicle wheel end systems has changed very little over the past 50 years. Current bearings for R-drive and trailer wheel end systems were designed between the 1920's and the 1960's and designs have essentially remained the same. Over the same period of time, considerable gains have been made in bearing design, manufacturing capabilities and materials science. These gains allow for the opportunity to significantly increase bearing load capacity and improve efficiency. Government emissions regulations and the need for fuel efficiency improvements in truck fleets are driving the opportunity for redesigned wheel end systems. The EPA and NHTSA standard requires up to 23% reduction in emissions and fuel consumption by 2017 relative to the 2010 baseline for heavy-duty tractor combinations.

This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.

This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.

This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.

For some years, OEMs and suppliers have been using CAD tools to improve efficiencies in both mechanical design and electrical design. Modern CAD tools have evolved from simple drafting and documentation towards specialized tools for each task – mechanical layout, mechanical styling, electrical design, manufacturing design, and so on. There is often a significant overlap between the data-scope of each of these tools, but, without good integration facilities, engineers must re-key the same information in each of the different tools: this is both time-consuming and error-prone. This paper examines, and illustrates, the issues, technologies and processes that are available to improve the integration between mechanical and electrical CAD tools, and between OEMs and their suppliers.

Provision of service information in various languages has been a must in the automotive industry. However, in the commercial vehicle industry, it is unclear how manufacturers are managing this daunting task. California Air Resource Board (CARB) 2010 regulations are awakening the commercial vehicle service information managers who are responsible for providing this information according to SAE J2403 terminology. Now is the time to mimic the automotive industry by collaborating on terminology, and in the meantime, begin discussion on how we all manage multiple languages.

Commercial vehicle manufacturers face unique challenges for the development of vehicle electronics systems. For one, customers typically have unique requirements coupled with an expectation of high reliability. Vehicle electronics is often the enabler for customized features. Ensuring that the vehicle will perform as demanded and promised adds a degree of burden on the vehicle manufacturers. Furthermore, the verification and testing of a large number of unique electronic system configurations is very expensive and time-consuming. This paper will explore how Model-Based Design can be used to meet these challenges and provide a high degree of confidence for both the manufacturer and the customer that requirements have been met. It will discuss factors to consider to support configurability, approaches for defining a system architecture that facilitates reuse, and capabilities for modeling state-based systems.

The work presents the design of a traction electric equipment set of an electromechanical drivetrain (EMD) to be used with 300-hp-class agricultural wheeled tractors. Comparative characteristics of various drivetrain types used in agricultural tractors are presented; and the advantages of using EMDs in tractors are discussed. The EDM advantages are as follows: improved technical and economic parameters of the tractor; reduced dynamic loads on the tractor and diesel units; reduces wheel slippage; reduced fuel consumption (by up to 30%); continuous variation of speed of the tractor and aggregated implements; reduced expenses on maintenance, repair and spare parts; increased total reliability, controllability and comfort; possibility to use the tractor as a power source (optionally). Considered in combination, all these advantages clearly speak in favor of using electromechanical drivetrains.

The work describes a concept application that aids a safety engineer to create a layup of equipment models by using an image scan of a schematic and a library of predefined standard component and their symbols. The approach uses image recognition techniques to identify the symbols within the scanned image of the schematic from a given library of symbols. Two recognition approaches are studied, one uses General Hough Transform; the other is based on pixel-level feature computation combining both structure and statistical features. The application allows the user to accept or edit the results of the recognition step and allows the user to define new components during the layup step. The tool then generates an output file that is compatible with a formal safety modeling tool. The identified symbols are associated to behavioral nodes from a model based safety tool.

Effective requirements elicitation and management is a common need in supplier-OEM relationships, and continues to play a vital role in all aspects of the product development lifecycle. While traditional methods address the business goals for requirements and provide guidance in ensuring the accuracy of the “Descriptive-Prescriptive-Explanatory” outputs for requirements gathering and documentation, engineering organizations continue to encounter challenges with respect to capturing and communicating change, accommodating the addition of relevant design details and efficient propagation to inform development. These challenges become more difficult to overcome in mechatronic systems, which combine mechanical systems with integrated software. As software development can produce an overwhelming volume of information that requires accurate tracking and proliferation, it cannot be effectively managed using traditional hardware-centric systems.